(2015-09-16, 08:50)trsqr Wrote:

(2015-09-16, 08:47)fritsch Wrote: Oki - please verify this. As drops would really suck and something is wrong.

Btw. the 4k@50 "test broadcasts" are 8 bit only? Nothing 10 bit here, yet?

Not sure about the 4k test broadcasts that Astra are currently doing - will need to take a look at this. The Astra demo videos on the demo-uhd3d.com site such as http://demo-uhd3d.com/fiche.php?cat=uhd&id=46 are 10-bit though, so they're a no-go with the Braswell of course...

EDIT: more info on Astra 4k: http://www.ses.com/ultra-hd
EDIT2: more satellite 4k channels over different satellites: http://en.kingofsat.net/ultrahd.php

(2015-07-12, 20:07)fritsch Wrote: Note: For the Jarvis version, you need to update the repository to install PVR addons, see: http://saraev.ca/oe/ (bottom notice) and install: http://saraev.ca/addons/v16/6.0/Generic/x86_64/repository.saraev.ca/repository.saraev.ca-1.0.0.zip repository

(2015-09-16, 09:18)fritsch Wrote: That's "Sync playback to display" - see the first post on the settings. It's only suggested if you don't use passthrough audio. On my setup I use PCM output "Adjust Refreshrate to match video" on start / stop and additionally: Sync Playback to Display.

(2015-09-15, 08:05)fritsch Wrote:

(2015-09-14, 23:57)ggp759 Wrote: The isengard based builds have resolved the 1080/24p a/v sync issues for me. Thanks for the hard work!

Thanks for this feedback, though Isengard is no solution - but old code. We need to fix that in our development version. So it would be cool if you could test from time to time. Btw. does it help, if you put the following advancedsettings.xml to /storage/.kodi/userdata directory:

Code:

<advancedsettings>
<video>
  <latency>
    <delay>0</delay>
    <refresh>
      <min>23</min>
      <max>24</max>
      <delay>0</delay> <!-- set to zero or adjust if audio seems out of sync with 24p movies -->
     </refresh>
  </latency>
</video>
</advancedsettings>

^^ For OpenELEC only if you have constant out of sync issues with our Jarvis build that has moved audio syncing to AE itself and therefore is technically superior.

(2015-09-15, 21:13)BigL-New Wrote: Kernel downloaded, installed and Bebox rebooted. I'll report any issues fund :-)

(2015-09-16, 15:16)FernetMenta Wrote: the point is that you can't adjust refresh rate to match video to a 100% match.

(2015-09-16, 13:54)ggp759 Wrote:

(2015-09-16, 09:18)fritsch Wrote: That's "Sync playback to display" - see the first post on the settings. It's only suggested if you don't use passthrough audio. On my setup I use PCM output "Adjust Refreshrate to match video" on start / stop and additionally: Sync Playback to Display.

I see thanks. These 2 terms were always confusing for me. I always choose "adjust refresh rate to match video" because i want video to play at the correct playback mode with no judder. Isn't "sync playback to display" the exact opposite of that? ie play a 24p video to much the ui's 60p refresh. Also i always use passthrough. Chromebox is connected to avr.