(2014-08-06, 07:41)DocG Wrote: In case there should be any doubts...

And yes, it does work for me.

(2014-08-06, 15:58)MattBlacK85 Wrote: Hi,

I'm using the standalone setup of OpenElec, now i want to restore to stock. So i made a ChromiumOS USB stick as said in the wiki. But i'm not getting any boot menu to choose to boot the USB. Did try booting with ESC or CTRL-L and CTRL-U with no luck. Can anybody tell me to get to the boot menu? Thanks in advance

(2014-08-06, 19:26)cquilliam Wrote: I'm still having issues with my MCE Remote. First off, I tried the openelec that's in this script that is supposed to have the fix built in already, and that didn't work.

Next I installed XBMCuntu standalone, and it didn't work. So, I followed the instructions on the wiki that pointed me to this post on Ubuntu forums. After performing the actions and rebooting, the remote still isn't working.

Edit: I should also add that this receiver works fine on my older Zotac MAG ION box on a USB2 port.

Code:

Bus 001 Device 004: ID 1784:0006 TopSeed Technology Corp. eHome Infrared Transceiver
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x1784 TopSeed Technology Corp.
  idProduct          0x0006 eHome Infrared Transceiver
  bcdDevice            1.00
  iManufacturer           1 TopSeed Technology Corp.
  iProduct                2 (error)
  iSerial                 3 (error)
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0020  1x 32 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0020  1x 32 bytes
       bInterval               0
Device Status:     0x0001
  Self Powered

Thoughts?

(2014-08-06, 20:17)Matt Devo Wrote: this MCE receiver is one that's still problematic due to it reporting an invalid bInterval value of 0, which the linux XHCI (usb3) controller driver is a bit more strict about than the USB2 controller. You can either wait for a patch, or pick up another receiver that's known to work (listed in the wiki)

(2014-08-06, 20:21)cquilliam Wrote: Alright, thanks Matt. And thanks for the work that you've been putting in on this, its much appreciated.

(2014-08-06, 23:20)MrCrispy Wrote: Isn't it better to get the PS3 BD remote (http://www.amazon.com/Media-Blu-ray-Remote-Control-Playstation-3/dp/B0050SX9I2). Its just as cheap and works with Chromebox, no need to buy a IR dongle.

(2014-08-07, 00:10)MrCrispy Wrote: Didn't know about that Since I have a Harmony smart control remote (it has both BT and IR) I guess I'm out of luck.

(2014-08-07, 01:51)hman333 Wrote: Any trick to getting the PS3 remote working? I have turned on BT, put remote in discovery. it shows up on the list and I click connect, it asks me for a pin and I have tried 1234 and 0000 with no luck. If I choose trust and connect it freezes up the box

Thanks

(2014-08-07, 01:52)Matt Devo Wrote:

(2014-08-07, 01:51)hman333 Wrote: Any trick to getting the PS3 remote working? I have turned on BT, put remote in discovery. it shows up on the list and I click connect, it asks me for a pin and I have tried 1234 and 0000 with no luck. If I choose trust and connect it freezes up the box

Thanks

As above, known issue with OE 4.1.2, not Chromebox specific